EFFECTS // ROBLOX STUDIO
How to make an impact effect in Roblox Studio
Use two ParticleEmitters in Roblox Studio to play a shell impact with a flash, thrown earth and smoke in 2 seconds, one for smoke and one for the glowing flame. Upload your 1024 px, 64-frame textures to each emitter, set FlipbookLayout to Grid8x8 and set FlipbookMode to OneShot.
- Godot 4 Available
- Unity Manual setup
- Unreal Engine Manual setup
- Roblox Studio Manual setup
- three.js Available
A draft compile is from $0.05, and new accounts start with $5 of usage.
01 // WHAT YOU GET
What you get for impact in Roblox Studio
The impact is a shell hitting dry ground: a bright flash, a spray of thrown earth and a little smoke, about 3.5 m wide and 2.8 m tall. Three emitters share one simulation: the flash is hot and short, and the earth is cold, so it falls back. It plays once in 2 seconds.
You get four PNG sheets of 64 frames, a layout.json with the timing, and previews, which you turn into a smoke texture and a flame texture, each on its own ParticleEmitter.
02 // BY HAND TODAY
Set up the impact in Roblox Studio by hand
- Ask your agent for the effect (for example "a mortar hit on dry ground that plays once") with
export.tile_px = 128, so each 8 x 8 sheet is 1024 x 1024 px, the largest image Roblox keeps. Also ask forexport.pacing = "even": OneShot spaces the frames evenly over Lifetime, and the example spends more frames on its fast start. - A ParticleEmitter takes one texture, so pack the smoke into one image: ask for
export.packto write the light from above (green ofmain_pos.png) into RGB and opacity (alpha ofmain_pos.png) into alpha. For the flame, make a second image on black:main_colour.pngtimes the squared alpha ofmain_neg.png, normalized to the clip's peak (how and why). - Upload each image in the Asset Manager and paste its id into the Texture of its own ParticleEmitter, both on one Attachment in the same part.
- Set FlipbookLayout to Grid8x8 on both emitters and FlipbookMode to OneShot with Lifetime 3.2 and Rate 0, then call
Emit(1)on both emitters when the impact happens, from the same script call and with identical fixed settings (layer alignment). - Flame emitter: LightEmission 1, LightInfluence 0, Brightness
scales.emit_max_hdr. Smoke emitter: LightEmission 0, LightInfluence 1. Set Size on both emitters to the meters per tile inlayout.jsonconverted to studs, a little over 12 studs for the impact.
03 // ADJUST IT
Adjust the impact for your scene
Use it for artillery, grenades, rockets and heavy hits. Ask your agent for a wetter, darker spray for mud, a smaller hit for bullets on dirt, or a stronger flash for a night map.
04 // SETTINGS
Settings in the impact spec
Three emitters share one simulation: a hot, short flash, cold earth that falls back, and a little smoke.
Ask your agent to change these and compile again; the full impact spec lists every value.
How do I get an impact effect for Roblox Studio?
Start from impact and ask your agent for a mortar hit on dry ground that plays once. Play the compiled textures in Roblox Studio.
How do I play the Roblox impact flipbook only once?
Set FlipbookMode to OneShot, Rate to 0 and Lifetime to 3.2 s, then call Emit(1) from a script after compiling with even pacing.
How do I make a realistic impact in Roblox Studio?
Use a simulated impact instead of painted particles. Three emitters share one simulation with a short hot flash, falling cold earth and light smoke.
How many frames does the Roblox Studio impact effect use?
The impact compile uses 64 frames over a 3.2 s clip and gives more frames to the fast burst at the start before ending cleanly.
Compile your first effect
You pay per compile and see the price before it runs. New accounts start with $5 of usage.