EFFECTS // THREE.JS

How to make an impact effect in three.js

In three.js, you can play a shell impact with a flash, thrown earth and smoke in 2 seconds. A snippet loads the packed RGBA sprite sheet on a THREE.Sprite, sets the texture repeat to one eighth, and removes it after the last frame. Godot 4 gets a ready scene that relights the smoke.

  • Godot 4 Available
  • Unity Manual setup
  • Unreal Engine Manual setup
  • Roblox Studio Manual setup
  • three.js Available

A draft compile is from $0.05, and new accounts start with $5 of usage.

IMPACTFINAL
First frame of the impact bake
Impact, 3.5 x 2.8 m, compiled with Spatial Compiler. Spec →

01 // WHAT YOU GET

What you get for impact in three.js

The impact is a shell hitting dry ground: a bright flash, a spray of thrown earth and a little smoke, about 3.5 m wide and 2.8 m tall. Three emitters share one simulation: the flash is hot and short, and the earth is cold, so it falls back. It plays once in 2 seconds.

You get four PNG sheets of 64 frames, a layout.json with the timing, and previews, which three.js plays through a small material.

02 // HOW TO

Play the impact in three.js

  1. Ask your agent for the effect (for example "a mortar hit on dry ground that plays once") with export.pack writing the light from above into RGB and opacity into alpha, so one PNG holds gray shading you can tint. (main_pos.png as it comes holds three light directions in RGB, not a color.) Load it with TextureLoader and set texture.repeat.set(1 / 8, 1 / 8).
  2. Put it on a THREE.Sprite with a SpriteMaterial (transparent: true, depthWrite: false) so it always faces the camera. For the flame, make a second texture in an image editor, main_colour.png multiplied by the alpha of main_neg.png squared, and draw it on a second sprite with THREE.AdditiveBlending. That texture is normalized, so restore the peak on the flame sprite with material.color.setScalar(emitMax), where emitMax is scales.emit_max_hdr.
  3. Each frame, pick the tile: column i % 8 and row Math.floor(i / 8), then set texture.offset.set(col / 8, 1 - (row + 1) / 8).
  4. The impact's frames crowd its fast start, so pick i from the clock: i = layout.frame_times_s.findIndex((t) => t >= elapsed). When that returns -1, after 3.2 s, call sprite.removeFromParent() and material.dispose().
  5. Set sprite.scale.set(s, s, 1) with s the meters per tile from layout.json, a little over 3.5 m for the impact, so it shows at its real size.

03 // ADJUST IT

Adjust the impact for your scene

Use it for artillery, grenades, rockets and heavy hits. Ask your agent for a wetter, darker spray for mud, a smaller hit for bullets on dirt, or a stronger flash for a night map.

04 // SETTINGS

Settings in the impact spec

Three emitters share one simulation: a hot, short flash, cold earth that falls back, and a little smoke.

Ask your agent to change these and compile again; the full impact spec lists every value.

06 // FAQ

Questions about impact in three.js

All questions →

README.THREEJS_IMPACT
How do I play an impact effect once and remove it in three.js?

Pick each frame from layout.frame_times_s, stop after frame 63 at 2 seconds, then call sprite.removeFromParent() and material.dispose().

How do I make a realistic impact effect in three.js?

Start from a simulated impact instead of manual particles. Three emitters share one simulation: a hot flash, falling earth and smoke.

How do I keep an impact effect in proportion in three.js?

Keep the Sprite square because every tile is square. Set sprite.scale.set(s, s, 1) using the meters per tile from layout.json.

How many frames does the impact effect use?

The impact compile uses 64 frames over 2 seconds and gives more frames to the fast burst at the start.

Compile your first effect

You pay per compile and see the price before it runs. New accounts start with $5 of usage.

All effects, guides and explainers →