EFFECTS // ROBLOX STUDIO
How to make a fireball in Roblox Studio
Use two ParticleEmitters in Roblox Studio to play a fireball that bursts from the ground and rolls upward in 3.7 seconds, one for smoke and one for the glowing flame. Upload your 1024 px, 64-frame textures to each emitter, set FlipbookLayout to Grid8x8 and set FlipbookMode to OneShot.
- Godot 4 Available
- Unity Manual setup
- Unreal Engine Manual setup
- Roblox Studio Manual setup
- three.js Available
A draft compile is from $0.05, and new accounts start with $5 of usage.
01 // WHAT YOU GET
What you get for fireball in Roblox Studio
The fireball is a fuel explosion that bursts from the ground, swells, rolls at its edge and rises, about 9.4 m wide and 13.4 m tall at its peak. It plays once over 3.7 seconds. More of its 64 frames go to the fast first moments, so the burst does not look choppy.
You get four PNG sheets of 64 frames, a layout.json with the timing, and previews, which you turn into a smoke texture and a flame texture, each on its own ParticleEmitter.
02 // BY HAND TODAY
Set up the fireball in Roblox Studio by hand
- Ask your agent for the effect (for example "a fireball about half the size of the example, played once") with
export.tile_px = 128, so each 8 x 8 sheet is 1024 x 1024 px, the largest image Roblox keeps. Also ask forexport.pacing = "even": OneShot spaces the frames evenly over Lifetime, and the example spends more frames on its fast start. - A ParticleEmitter takes one texture, so pack the smoke into one image: ask for
export.packto write the light from above (green ofmain_pos.png) into RGB and opacity (alpha ofmain_pos.png) into alpha. For the flame, make a second image on black:main_colour.pngtimes the squared alpha ofmain_neg.png, normalized to the clip's peak (how and why). - Upload each image in the Asset Manager and paste its id into the Texture of its own ParticleEmitter, both on one Attachment in the same part.
- Set FlipbookLayout to Grid8x8 on both emitters and FlipbookMode to OneShot with Lifetime 4 and Rate 0, then call
Emit(1)on both emitters when the fireball happens, from the same script call and with identical fixed settings (layer alignment). - Flame emitter: LightEmission 1, LightInfluence 0, Brightness
scales.emit_max_hdr. Smoke emitter: LightEmission 0, LightInfluence 1. Set Size on both emitters to the meters per tile inlayout.jsonconverted to studs, a little over 48 studs for the fireball.
03 // ADJUST IT
Adjust the fireball for your scene
Use it for vehicles, fuel tanks and big set pieces. Ask your agent for a smaller fireball, a darker smoke cap, or several seeds so a chain of explosions does not repeat the same shape.
04 // SETTINGS
Settings in the fireball spec
A short burst of hot fuel starts at ground level and burns only where it meets air, so the ball burns at its rolling surface instead of all at once.
Ask your agent to change these and compile again; the full fireball spec lists every value.
How do I get a fireball effect for Roblox Studio?
Start from fireball and ask your agent for a fireball at half the size that plays once. Play the compiled textures in Roblox Studio.
How do I play the Roblox fireball flipbook only once?
Set FlipbookMode to OneShot, Rate to 0 and Lifetime to 4 s, then call Emit(1) from a script after compiling with even pacing.
How do I make a realistic fireball in Roblox Studio?
Use a simulated fireball instead of painted particles. A short burst of hot fuel starts at ground level and burns where it meets air.
How many frames does the Roblox Studio fireball effect use?
The fireball compile uses 64 frames over a 4 s clip and gives more frames to the fast burst at the start before ending cleanly.
Compile your first effect
You pay per compile and see the price before it runs. New accounts start with $5 of usage.